Automation Specialist jobs in Alamogordo, NM

Job Title:   Automation Specialist

Schedule:   7/7 (Mancamp Available)

Location:    Mentone, TX

Pay:  DOE

Danos Expectations: A successful candidate will exhibit characteristics that support the following:

• Safety Awareness
• Work Ethic
• Technical Skill
• Customer Focus
• Open Communication
• Implementing Vision and Values

 Our purpose, values and high-performance culture traits are fundamental to our success and offer wonderful opportunities for employee development.

Job Duties:

• Install, maintain, inspect, troubleshoot, repair and perform preventative maintenance on all field instrumentation, control systems, analyzers and electrical equipment including Injection well controllers, facility PLC's and producing substations; measure and troubleshoot low voltage and DC devices including transmitters, actuators, radios, flow meters; able to connect and troubleshoot PLC's. utilizing Rockwell Automation software including Allen Bradley, FactoryTalk, Studio 5000, Logic 500
• Responsible for prompt and accurate diagnosis of minor problems and the implementation of corrective action. Consult directly with equipment vendors on problems for resolution as necessary.
• Coordinate and conduct well maintenance activities on wells and batteries for maintenance, upgrades, recurring problems where root cause cannot be identified by Well Tech
• Coordinate and conduct maintenance activities on end devices to include pre-programming of transmitters and ensure data accuracy on all fluid and gas measurement meters.
• Leverage CMMS, such as SAP, to facilitate the processes of maintenance operations.
• Conduct in depth failure analysis on repeat equipment failures.
• Ensure design for wells are within guidelines of automation standards.
• Respond and provide automation support during all outages.
• Work off of assigned schedule and maintain zero out of compliance work orders.
• Provide analytical support on problem wells.
• Provide input on new technologies.
• Assist other technicians during storm outages to bring wells back online.
• Able to perform general PM work: testing end devices, temperature shutdowns, pressure switches, level shutdowns.
• Conduct evaluation tests on valves, motors, instruments, etc.
• Knowledge of RTUs. Understanding of digital and analog I/O, programming, and troubleshooting
• Must be proficient in troubleshooting using schematics, ladder logic, electrical one-line, and P&I drawings.
• Proficient in maintaining process control loops, electronic controls, valves, and transmitters.

Competencies:

• Advanced computer skills (MS Office Suite, proprietary software, etc.)
• Strong initiative and self-starter
• Ability to perform under pressure.
• Demonstrate ability to perform strong time management skills.
• Ability to keep neat and accurate records.
• Multi-task orientation with skills related to work prioritization.
• Ability to implement cost effective solutions.
• Ability to work with a team and communicate with other functions.
• Excellent diagnostic and repair skills for complex problems in automation systems
• Excellent knowledge of automation host systems
• Expert in using test equipment pertaining to job, including oscilloscope, function generators, radio service monitor, etc
• Understanding of pneumatic instrumentation: calibration and maintenance
• Skillful in reading electronic schematics, identifying components, and understanding their functions.
• Able to calibrate and troubleshoot complex PLC programs.
• Competent level of understanding of automation and electrical design principles
• Understanding of PSSRs and MOCs
• Extensive expertise in EOR safe work systems
• Extensive expertise of Electrical / Automation construction codes and practices.
• Extensive knowledge of material specifications and application.
• Understanding of regulatory guidelines.
• Be knowledgeable with tagging conventions, programing simulation and testing.
• Strong analytical and problem-solving skills
• Good working knowledge of SAP
• Understanding of Importance of environmental and Safe Work Practices

Requirements:

• High School Diploma or GED equivalent required; Applied Science Degree in Instrumentation & Electrical or Electronics Technology preferred
• Two (2) or more years of Oil & Gas Land Automation/I&E Specialist experience and working knowledge of oil and gas land production operations. 
• Must have experience with the following:  Injection Well Controllers, Facility PLC's, substations, measure and troubleshoot low voltage and DC devices including transmitters, actuators, radios, flow meters; strong PLC troubleshooting a must.
• Must be experienced with Rockwell Automation software including Allen Bradley, FactoryTalk, Studio 5000, Logic 500
• Advanced knowledge of analog and discrete instrumentation and various serial and ethernet communications protocols
• Advanced knowledge of well RTU designs, programming and troubleshooting
• Intermediate knowledge of maintaining PLC programs in function block, ladder logic and structured texts
• Intermediate knowledge of maintaining local HMI operator interfaces
• Ability to work effectively in a team environment as well as by self without direct supervision.
• Electronically qualified per OSHA, 1910.269 up to 600V
• Physical requirements – Must be able to lift 40 lbs., climb ladders and stairs. Walking, bending, stooping is required. Must be able to wear personal protective equipment including the use of a respirator. Must be able to respond to visual and audible alarms.
• Must be able to work 12 hr. days, with shift beginning on Wednesdays at Noon.
• Valid Driver’s License with an acceptable driving record
• Must be able to meet all conditional job offer requirements including background, drug screen, hair follicle, agility, fit for duty.